6W LED MR16 Review
General Information
| ID | #62 |
|---|---|
| SKU | 120670 |
| Series | N/A |
| Manufacturer | Lucci LEDlux (other LEDs from Lucci LEDlux) |
| Fitting Type | MR16 (other MR16 LEDs) |
| Light Type | Downlight (PAR) |
| Height | 65mm |
| Diameter | PAR16 (50mm) |
| Weight | 65g |
| Warranty | 1 Years |
| Test Date | 2013-05-01 |
| Review Notes | This is a MR16 retofit downlight. But it is hard to recommended. This LED would not be powerful enough to use as a replacement for a 50W halogen, which are typically 4 times brighter. While the efficiency is a better than a halogen, it is no where near as good as other LED downlights, including others from the Lucci LEDlux range. |
| Price | $36.95 (AUD) from Beacon Lighting on 25th of March 2013 |
| Rating |   |
|---|
LED Specifications
| Claimed | Measured |
Compared To |
|
|---|---|---|---|
| Watts | 6W | 5W @ 12V Electronic Transformer | 54.7W @ 12V |
| Yearly Running Cost[?] | $1.31 | $1.10 | $11.98 |
| Lumens | 170 lm | 168 lm | 765 lm |
| Efficiency[?] | 28 lm/W | 34 lm/W | 14 lm/W |
| Lumens/Purchase Price | 5 lm/$ | 5 lm/$ | 170 lm/$ |
| Power Factor[?] | N/A | 0.65 | 1 |
| Color [?] | Warm White, 2700K | Warm White, 2721K | Warm White, 3015K |
| Angle[?] | 45° | 42° | 45° |
| Dimmable | Not Dimmable | N/A | Yes, Trailing Edge |
| CRI (Color Accuracy)[?] | N/A | 81 | |
| Life | N/A | Not Measured | 6,000 hours |
| Min/Max Voltage | 12V / 12V | N/A | |
| Min/Max Temperature | N/A / N/A | N/A | |
| Measured Temperature | 50°C @ 25°C ambient 122°F @ 77°F ambient |
256°C @ 25°C ambient 493°F @ 77°F ambient |
|
| Flicker Percent[?] | 79% | 3% | |
| Flicker Index[?] | 0.199 | 0.008 |
Advertisement
Distribution Graph
Angle: 42° (±21° from bottom), Maximum lux:
Graph notes: Shows the intensity of the light when viewed from different angles. Normal omni-directional globes have a fairly constant output all the way around (excepting directly above). Downlights have a narrow range at the bottom in which the light is emmited, this determines their angle.
Spectrum Graph
Graph notes: Shows the breakdown of the LED light into its component colors. With short wavelength ultraviolet on the left and long wavelength infrared on the right. The green line represents the relative absolute strength of the light at each frequency, while the red line represents what the typical human eye would see. The human eye is most sensitive to green light, but much less sensitive to purples and deep reds.
Flicker Graph
Percent: 79%, Index: 0.199 (lower is better in both cases)
Graph notes: Shows variation in light output over 1/10th of a second, with relative light output on the Y axis and time on the X Axis. Measured with a photodiode connected to an Oscilloscope. Ideally the yellow line should be flat. Low frequency high amplitude waveforms mean there is a possibility of noticeable flicker, but sensitivity to flicker varies between people. [More details about LED flicker]
Disclaimer: While every effort has been made to ensure the accuracy of these results, each measurement carries an inherent degree of uncertainty and error. Safety and EMC compliance of products to regional or international standards have not been verified unless noted as an ENERGY STAR® LED Lighting Facts, or SSL Quality Scheme certified product. Retailers and importers selling unmarked or unapproved electrical goods can be fined or imprisoned. Mains supplied downlights require installation by a licensed electrician.